product review overlay image

Product Description

Oxford Cutmaker Plasma models, offer exceptional cutting performance on all metals. Our design gives a tightly constricted arc minimising kerf
width & maximising cut capacity & speed. This results in a very straight clean cut with minimal dross. Even on thick materials such
as 30 or 40mm the cut will be clean & close to perfectly straight. Compared with a low cost imported plasmas the performance
difference is almost unbelievable. Compared to using oxy-fuel (gas bottles) cutting speed can be more than 5 times as fast &
operating costs coming out at around 90% reduced, you also get a better cut quality.
Drag cutting parts are fitted to all hand torches, drag cutting is the easiest & neatest option for hand plasma, it gives better access
than other plasma torch designs & allows you to follow straight edges or templates with ease. In addition, a range of extended
consumables are available for getting into those tight tricky jobs. For cutting below 50A its also possible to carry out tip contact
cutting, dragging the cutting tip directly on the job gives even more precision & visual access to the cutting point.
CUTMAKER models can also cut the very thinnest of metals with absolute precision, smaller models using the P75 torch work
especially well from 0.5mm upwards. Models fitted with the P130 can use the optional ‘fine cut’ consumables to give similar results.
Mechanised cutting performance is exceptional, just plug in our P75M or P130M machine torch & fit the CPC connector then you
are ready to use on cutting tables, straight line cutters, robot etc. CNC interface uses the same wiring as US made machines, start
signal, OK to move contact & we also have adjustable divided arc volts. This can be set to give 20:1, 30:1, 40:1, 50:1 & anything in-
between. This gives compatibility with all known cutting tables & THC systems.

Thermal gouging
These models all give great gouging performance from small light jobs right up to the heaviest plate. The arc stretch is unbeatable
giving you smoother finishes & better control. Remove welds, wear plates, create weld preps, etc. Can also be used for automated
gouging with robots or Gullco carriages & tractors. For gouging use simply replace the tip & shield for gouge parts & reduce air
pressure by around 1 bar.
Metal marking
Our metal marking function allows fast clean marking of metals for both automated & manual use. Mark drill points, fold marks, add
your logo, date code, ID, etc. Unlike competitors’ products we use standard cut consumables, so move from cutting to marking in a
second!
Thermal heating
A fast source of direct heat for manual use, mainly to assist with the removal of seized nuts, bearings, & light preheating jobs. This
function provides 1.8kw / 2.7kw output of intense instant heat far hotter than propane or butane torches produce. It’s also a more
direct & controllable heat so heats only the item you need heating, the torch cooling air keeps everything else at a low temperature.
For instance when removing seized nuts propane torches tend to heat the nut & bolt, Cutmaker plasmas can heat the nut & leave
the bolt relatively cool, allowing the nut to be removed quicker.
The following are typical times to heat nuts to cherry red. M5 – 3 secs, M6 – 5 secs, M8 – 8 secs, M10 – 14 secs, M12 – 20 secs.
In addition, thermal heating function can be used to bend plastic parts or for plastic welding.
Thermal heating can be done with cutting consumables fitted for a tight heat focus or gouging parts fitted for a softer wider arc.

OPERATORS MANUAL

Technical Data

Input fuse - slow 16/20/25A* 230V 1ph
Maximum severance cut 30mm steel
Max recommended clean cut 18mm
Maximum pierce 12mm
Output range 15A-45A
Maximum output power 45A @138V (6.2kw)
Duty cycle @ full power 50% @ 45A
100% duty cycle 33A
Min generator size for 100% rating* 5.5KVA
OCV -no load voltage 300V
Thermal heating output power 1.8KW
Thermal heating duty cycle 50%
Maximum cutting speed 6mm steel 2M/min
Maximum cutting speed 10mm steel 1M/min
Maximum cutting speed 15mm steel 0.46M/min
Maximum cutting speed 20mm steel 0.25M/min
Maximum cutting speed 25mm steel 0.14M/min
Maximum cutting speed 30mm steel 0.1M/min
Air requirements 5 Bar@ 170L/min (4 Bar gouging)
Standard torch supplied P75 4M with quick connect
Weight approx with torch 16kg
Size W x H x L 240 x470 x 560

Specifications

Input power voltage (V)
230V
Brand
Oxford
Product Code
Cutmaker 451

Delivery & Returns

UK Delivery

Postage and packing to mainland UK is free on all orders over £60.00 (exc VAT. All orders up to £60.00 (exc VAT) are £5.75 plus VAT.

Click and collect is now available for PO and SO postcodes.

Outside of the UK

For delivery to an address outside the UK please call us on 023 92 295612 or email us at sales@migtigarc.co.uk and we will advise.

Oxford Cutmaker 451 Plasma Cutter

Product Code Cutmaker 451

Key Features

Non HF pilot start

Thermal heating function

Metal marking function

Mesh cutting function

Generator friendly